Redesigning a Yagi
#1
I have been toying with the idea of building something like this 20m Yagi, only redesigning it for 15m.

https://www.nonstopsystems.com/radio/pdf...i-yagi.pdf

Can anyone suggest any references  or calculators that might assist?

The idea is a for bit of practical learning and also a bit of 'shed time'.

TIA
Colin
Barossa Valley, SAP. PF95ln
(aka VK5CSW)
Reply
#2
Consider each half element a loaded 1/4 wave whip and use something like this to determine your inductor when scaling :
https://m0ukd.com/calculators/loaded-qua...alculator/
It won't be exact but will provide a guide. 

Remember to scale the spacing between REFlector / DIRector and Driven Element too.  A DE plus DIR usually gives slightly better gain than a DE plus REF when dealing with 2 element arrays.

Typically tune the DE to desired frequency, a DIR to about 5-10% higher, a REF to 5-10% lower.

Final tip:  don't actually cut the excess wire length (stage 8 step 2) when going through the tuning process - simply fold it back along the element length initially. Once the proper tuning point is found, only then do you trim the folded-back wire.
Doug VK4ADC @ QG62LG51
http://www.vk4adc.com

This Forum is only going to be as interesting as the posts it contains. 
If you have a comment or question, post it as it may trigger or answer the query in someone else's mind.
Reply
#3
(10-10-2018, 07:34 PM)VK4ADC Wrote: Consider each half element a loaded 1/4 wave whip and use something like this to determine your inductor when scaling :
https://m0ukd.com/calculators/loaded-qua...alculator/
It won't be exact but will provide a guide. 

Remember to scale the spacing between REFlector / DIRector and Driven Element too.  A DE plus DIR usually gives slightly better gain than a DE plus REF when dealing with 2 element arrays.

Typically tune the DE to desired frequency, a DIR to about 5-10% higher, a REF to 5-10% lower.

Final tip:  don't actually cut the excess wire length (stage 8 step 2) when going through the tuning process - simply fold it back along the element length initially. Once the proper tuning point is found, only then do you trim the folded-back wire.

Thanks Doug.

Having a read now.
Colin
Barossa Valley, SAP. PF95ln
(aka VK5CSW)
Reply
#4
When I started AR in the 1960's aluminum was very hard to come by (at least in ZL) and many HF and VHF beams were made of timber, usually Oregon pine (very hard to get now) or bamboo, with wire elements. Coax was also hard to get and costly so these beams were fed with open wire line and they worked very well.

Colin, this is an interesting design, but have you considered a Moxon? They have a small footprint and can be made with light timber and wire and you can nest the wire elements for several bands fed with a single feed line.  I made one for 10 and 15m with an X shaped frame held together with a central bolt so it could be folded for portable use. It worked very well.

73

Wayne
Reply
#5
Decisions, decisions, decisions...

The yagi could be smaller, but the moxon could be collapsible.

Why do I always end up in analysis paralysis when thinking about antennas?
Colin
Barossa Valley, SAP. PF95ln
(aka VK5CSW)
Reply
#6
(12-10-2018, 02:15 PM)VK2CSW Wrote: Decisions, decisions, decisions...

The yagi could be smaller, but the moxon could be collapsible.

Why do I always end up in analysis paralysis when thinking about antennas?

Just remember the old ham adage: Any antenna in the air is always much better than any antenna still inside your head Big Grin Just get something up there lad! Rolleyes

Wayne VK4WDM
Reply
#7
Quote:When I started AR in the 1960's aluminum was very hard to come by (at least in ZL) and many HF and VHF beams were made of timber, usually Oregon pine (very hard to get now) or bamboo, with wire elements.

Or copper pipe on a timber mast.

Don't remember where it came from but my first 3 el 2m Yagi in ZL (also in the 60's) was copper pipe with a coax feed.
Terry VK5TM
https://www.vk5tm.com
Reply
#8
(12-10-2018, 02:15 PM)VK2CSW Wrote: Decisions, decisions, decisions...

The yagi could be smaller, but the moxon could be collapsible.

Why do I always end up in analysis paralysis when thinking about antennas?

Easy. Build both.
Reply
#9
(13-10-2018, 09:14 PM)VK5TM Wrote:
Quote:When I started AR in the 1960's aluminum was very hard to come by (at least in ZL) and many HF and VHF beams were made of timber, usually Oregon pine (very hard to get now) or bamboo, with wire elements.

Or copper pipe on a timber mast.

Don't remember where it came from but my first 3 el 2m Yagi in ZL (also in the 60's) was copper pipe with a coax feed.

copper pipe with a coax feed!    You must have come from a wealthy farm.  My first antennas were made with fencing wire, held up with binder twine and fed with twin electric light cord Tongue 

Wayne VK4WDM.
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)